Martinez-Pampliega, R. (Roberto)
- Publications
- item.page.relationships.isContributorAdvisorOfPublication
- item.page.relationships.isContributorOfPublication
4 results
Search Results
Now showing 1 - 4 of 4
- Densification of WC-Fe-Ni-Co-Cr cemented carbides processed by HIP after sintering: effect of WC powder particle size(Elsevier, 2023) Lozada-Cabezas, L. (Lorena); Moreno, J.M. (José Manuel); Ibarreta-Lopez, F. (Federico); Martinez-Pampliega, R. (Roberto); Navarrete-Cuadrado, J. (Jazmina); Soria-Biurrun, T. (Tomás)Shrinkage, liquid formation and mass losses of WC-19 vol% FeNiCoCr alloys during sintering have been inves- tigated in compositions either with coarse or submicron WC powders. Mass losses detected by thermogravimetry are compatible with carbothermal reduction of the different oxides present in the powder mixtures. Hardness and fracture toughness of materials based on submicron WC powders are within tolerances of those reported for WC- Co materials with similar microstructures. However, fracture strength is approx. 25% lower.
- Effect of carbon content and cooling rate on the microstructure and hardness of TiC-Fe-Cr-Mo cermets(2024) Isasti-Gordobil, N. (Nerea); Lozada-Cabezas, L. (Lorena); Sánchez-Moreno, J.M. (José Manuel); Ibarreta-Lopez, F. (Federico); Martinez-Pampliega, R. (Roberto); Navarrete-Cuadrado, J. (Jazmina); Soria-Biurrun, T. (Tomás)TiC-FeCrMo cermets have been obtained in fully dense form by Sinter HIP at 1400 degrees C. Significant microstructural changes have been observed in these materials for relatively small variations in their carbon content after sintering. In the cermets with higher carbon content Cr-rich likely M7C3 carbides are observed to precipitate at the (Ti1-x,Mo-x)(y)C-z - metal interface. In addition, these cermets present a significant amount of retained austenite as part of the metal matrix. No retained austenite and many fewer M7C3 carbides are found in alloys with a reduction of 0.2 wt% in the total C content. Continuous cooling diagrams have been obtained from an austenitizing temperature of 950 degrees C. Hardness increases by 30% with respect to that of as sintered specimens after cooling at 1 degrees C/s confirming that these TiC-FeCrMo cermets are suitable for hardening by air-quenching. At this cooling rate, it is observed that the relatively small carbon changes mentioned before have a significant effect on the bainitic transformation, displacing its onset to higher temperatures as the C content is reduced. Slower cooling rates result in complex microstructures, in which, in addition to martensite, ferritic bainite, M7C3 and M23C6 carbides are also found. Microstructure and hardness of TiC-FeCrMo materials can be modified by the use of standard heat treatments to obtain a wide variety of mechanical properties suitable for certain hot rolling applications.
- Microstructure, mechanical properties and fracture behavior of NiCoCrTiAl and FeNiCoCr new alternative binders for WC based hardmetals(Elsevier, 2022) Lozada-Cabezas, L. (Lorena); Sánchez-Moreno, J.M. (José Manuel); Ibarreta-Lopez, F. (Federico); Martinez-Pampliega, R. (Roberto); Navarrete-Cuadrado, J. (Jazmina); Soria-Biurrun, T. (Tomás)Hardness and fracture strength of WC-Ni-Co-Cr-Ti-Al cemented carbides have been measured at room temperature in as-HIPed and solution-aged conditions. These treatments are applied to modify the size of gamma prime precipitates, which are intrinsically formed within the metallic binder of these ceramic-metal composites during the sintering process. Compositions containing approx. 28-29 vol% metal content exhibit hardness values in the range of those reported for similar grades of WC-Co hardmetals. Optimized aluminum additions lead to materials with fracture strength values only 15% lower than those reported for the same WC-Co commercial references. These results suggest gamma prime precipitation hardening as a potential strategy for improving the performance of WC-Co materials at high temperatures. Regarding Fe-Ni-Co-Cr alloys are potential candidates for partial substitution of Co content in WC-based hardmetals. It has been investigated WC coarse grade with 15 wt%(FeNiCoCr). The Cr content has been adjusted in order to avoid the precipitation of M7C3 carbides. Within the corresponding carbon windows, fracture strength values range from 2.8 GPa to 3.0 GPa. These values are within the range of standard WC-Co grades with similar binder contents and WC grain sizes.
- Effect of chromium and carbon contents on the sintering of WC-Fe-Ni-Co-Cr multicomponent alloys(Elsevier, 2020) Lozada-Cabezas, L. (Lorena); Sánchez-Moreno, J.M. (José Manuel); Ibarreta-Lopez, F. (Federico); Martinez-Pampliega, R. (Roberto); Soria-Biurrun, T. (Tomás)WC-Fe-Ni-Co-Cr cemented carbides have been obtained by liquid phase sintering from WC-Fe-Ni-Co-Cr3C2 powder mixtures. Taking the 40wt%Fe-40wt%Ni-20wt.%Co alloy as a reference, new binder phases has been prepared by introducing controlled amounts of Cr and C, via Cr3C2 and C black powders respectively. As described for WC-Co-Cr materials, Cr additions are observed to reduce the eutectic temperatures of the WC-Fe-Ni-Co system. First liquids detected on heating exhibit wide temperature melting ranges, which become narrower and are displaced to higher temperatures on repeated heating and cooling cycles. Apart from the decarburization associated to the carbothermal reduction of powder oxides, this phenomenon could be also associated to the homogeneization of the chemical composition of these multicomponent binder phases, which is faster as C content decreases. Correlation between experimental melting and solidification temperature ranges and those predicted by Thermocalc (R) is better as Cr content increases. Experimental C windows, defined in this work by the absence of free C or. phases, are located at C contents higher than those estimated by Thermocalc (R). Although the 40wt.%Fe-40wt.%Ni-20wt.%Co alloy is austenitc, BCC phases are partially stabilized at low C and high Cr contents. Although these compositions are free from. phases or free C, a precipitation of Cr-rich carbides is found at the WC-metal interface. These precipitates are not observed in the alloy with 0.75 wt% Cr (i.e. 5 wt% of the nominal metal content) and 5.39 wt%C. This C content is 0.17 wt% higher than that predicted for precipitation of M7C3.